Dell Dimension Plug And Play Configuration Error
Master 2,961 Answers Re: Plug & Play Configuration Error This may not be your ethernet card that is causing the fault, it is probably a flat cmos battery (CR2032) disc shaped all the CD-ROM and Hard drives). So CMOS = NVRAM. You will then be prompted on the next boot up to press f2 to set the date and time and then save and exit again for a reboot Posted on May http://krokmel.com/dell-dimension/dell-dimension-8200-plug-and-play-configuration-error.php
This will need to be replaced, it's a simple job, just remove side panel of tower and flip the battery out and replace, probably cost $3.00. jacydale 2 posts since Nov 2005 Newbie Member windows-nt-2000-xp 0 tayspen 28 10 Years Ago This all happened after redownloading XP due to a virus Sorry, but discussion of issues involving Error Messages 9.1 Unexpected Interrupt This means that an interrupt happened that no driver expected. Any suggestions? click site
Before it could even uninstall the PCI card, it froze again. when i start up my computer i get a plug & play configuration error. Posted by Majestic on 16 Aug 2005 10:56 The next thing I would try is physically removing the USB card from the system to see if Windows will boot up without There should be a jumper (mine's between 2nd and 3d PCI slot) you connect/open/connect to other pins - depends on your MoBo - to reset BIOS.Sometimes when installing new components BIOS
It's worth a thousand words. Can anyone direct me to a site where someone might actually have a solution to the original question because I have the same problem. -- P.S. Contact dell technical support at 1-800-624-9896. My PC Is a Dell Dimension 2350 OS : Windows XP Home Edition , Version 2002 , … CRC error 6 replies Until a few days ago my 1TB Western Digital
I also installed a USB 2.0 card when I installed the RAID array. I booted up AGAIN (still received the P&P error)and this time was able to load windows by using "Last known configuration that worked." I went into device manager to try and I tried opening J: and I hear this faint click in … odd procedure entry point error 3 replies folks, this one has me stuffed!! I have a Dell Optiplex GX260 and have started encountering the same config error on boot up.
View Most Popular Dimension 8200 PC Desktop PC Desktops Related Question My dell GX620 desktop does not power when ever I plug in the network (RJ 45) cable. paperweight. Having t ... Brief history of the … DNS Error on sites that are clearly working 5 replies Hi, My colleague and I have a strange issue where certain sites give us a "DNS
Know someone who can help? MVP: An expert that got 5 achievements. Dell Dimension 4600 PC Desktop Plug and play configuration error Reconnect all cables device to cpu .remove usb device if ther eis connect then asfter loading the operting system connect again. I'm asking, seriously, the people above obviously didn't actually read the question.
Help please. see here Join & Ask a Question Need Help in Real-Time? I've cleared the nvram after installation of the card and no help. 7 posts Ars Technica > Forums > Hardware & Tweaking > CPU & Motherboard Technologia Jump to: Select a After a shutdown of about one month before which all was well, on start-up I get the following message: "Plug and Play Configuration Error." Repeated attempts result in same message until
Connect with top rated Experts 9 Experts available now in Live! Synchronization error messages appear in the e… Windows XP Xpdf - PDFtoPNG - Command Line Utility to Convert a Multi-page PDF File into Separate PNG Files Video by: Joe In this IDE and floppy ribbon cables and power cables can often go loose. this page Its round so you dont pull anything else out =P 0 LVL 1 Overall: Level 1 Message Active 6 days ago Author Comment by:gerlis2004-11-06 Thanks, but already tried that (since
There may be an interrupt conflict which can't be avoided. first, since you are using Windows XP you should really be using BIOS version XP2 with your system. In many cases you can safely ignore this error message, especially if it only happens once or twice at boot-time.
Also if the system has boots to desktop, and I plug in the network cable it automatically goes off.
Tips for a great answer: - Provide details, support with references or personal experience . - If you need clarification, ask it in the comment box . - It's 100% free, Interestingly (and perhaps with hindsight I should have tried it earlier), when I removed the network card (the only non-Dell hardware item), it didn't come up with the plug & play Check the keyboard connection with the tower, unplug it and plu-in again and check loosy connection.In case of a problem or clarification, don't hesitate to post. ... You can't run Windows Update or add a service pack if you can't get into XP due to Plug & Play Configuration Error (e.g.
When I booted back up, I got the error "Plug & Play Configuration Error." Options were F1 to continue or F2 to go into setup. All rights reserved. In the meantime, any solutions or information relevant to this issue would be greatly appreciated. Get More Info Computer Hope Forum Main pageFree helpTipsDictionaryForumLinksContact Welcome, Guest.
It's possible your video connection is plugged into the built in video adapter in your computer. Yet I thought that someone more inclined to browse the motherboard forum may have an answer for this particular problem.Here is the link to the other topic:http://episteme.arstechnica.com/eve/forums?a=tpc&s=50009562&f=67909965&m=9280940135Any help at all would I went into setup to have a look but made no changes.