Canon Error 343
Note: if the capacity of the absorption pad is unclear, register a value corresponding to the quantity of absorbed ink in pad Solution: Replace the PCNT PWB, and register a Solution: If the other party is using a Canon model then contact them and have them match the passwords. A. Solution: Replace the G3 modem control unit (MOD2 unit, etc.). ##237 [ RX ] DECODE control UPI malfunction. http://krokmel.com/canon-error/canon-error-061.php
Cause: Cannot receive signals properly due to poor line conditions. Solution: Print out all the data, clear the memory and then re-register data. It even delivers borderless copies and photos. Solution: Replace the modem or modem attached circuit board.
A. Cause: Defective internal unit Solution: Refer to Service manual ##336 [ TX / RX ] BJ head temperature malfunction. Solution: Take echo counter-measures as described in Service manual. Solution: Have the other party lower the transmission start speed to 4800 bps.
Solution: Press Start button after confirming the first DIS from the other party during a manual call. Solution: Replace the BJ cartridge B. Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##716 [ TX ] Fail to fall back during ARQ transmission. B.
ginrashid: i need reseter for canon pixma p200 please help... Cause: The ink detection sensor is faulty Solution: Replace the ink detection sensor Solution: Replace the unit containing the ink detection sensor. ##349 [ TX ] Home position Cause: Defective internal unit. Cause: The user telephone number is not registered; (if receiver is Ricoh 3000L).
Solution: Have the other party boost the transmission level for proper reception of the picture signal. Solution: Adjust the NL equalizer to properly receive the signals. Please do this at your own risk, there is always a small chance that you might mess up and break your printer. Category:Printers Share this conversation Expert: Sandeep Pamarati replied5 years ago.
Solution: Have the other party lower their transmission level so they will not receive echo signals. ##006 [ RX ] Failed phase synchronization from second sheet during G2 reception. A. Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##739 [ RX ] Exceed buffer memory during ARQ reception. Cause: The document was not set during polling.
Dec 02, 2007 | Canon SmartBase MP730 All-In-One InkJet... 3 Answers Error code ##343 We have just attempted to install an Cannon imageclass mp360 and the error message "check printer ##343" check my blog Aug 25, 2010 | Canon MultiPASS MP730 All-In-One InkJet... 1 Answer Waste ink near full waste ink is the container that collects excess ink during cleaning cycles. Solution: Replace the TONAL control unit (MOD2 unit, etc.). ##244 [ TX / RX ] OPT2 control unit malfunction. Solution: Have the other party lower the reception level to prevent the other party from receiving echo signals. ##113 [ TX ] Receive signals other than MFC, RTP, RTN, PIP
A. Solution: Replace the SCNT PWB ##261 [ TX / RX ] System error between modem and SCNT. Solution: Contact the telephone company and request line maintenance. ##010 [ RX ] Failed Phase synchronization on first sheet during reception in G2 or MF1. http://krokmel.com/canon-error/canon-error-05-fix.php Solution: Turn OFF the power and let machine cool for a while.
Did you mean? Solution: Power cycle the machine (unplug unit). Solution: Add a long pause after the telephone number when registering the user in the auto- dialing directory so that the system will not respond to the first DIS from the
Solution: Lower the transmission level so the echo of the CFR is not received. ##201 [TX / RX] DCN reception other than normal binary protocol.
Solution: Open printer body and remove foreign body. Powered by Blogger. A. A.
Solution: Replace the ink detection waste ink pad. Solution: Adjust the NL equalizer so the other party can receive picture or EOP signals properly. A. http://krokmel.com/canon-error/canon-error-020.php go to 'test mode' by pressing > several times when "test mode" is on the screen press the "ok" button. 4.