Brother Mfc-8840d Error Codes
You will need an engineer to replace the laser unit. If nothing is found, an engineer will be needed to determine the cause. I was about to call Brother but decide to search on the net first. Hi,A6 error means the CIS unit is defective and needs to be replaced.Unfortunately this can sometimes cost more to replace ...
Brother Mfc 8840d Driver
Finally I swapped the cartidges between the two machines.Bingo! The only thing that I can think of is that they think you need a firmware upgrade. If the error persists then the fuser unit will need replacing.
I held the menu on power up, got into maintenance, did the 91 reset, and 99 to exit - walla! Explanation: Switch the machine off and back on again. All fixed - and mine was a MFC 9180. - Anonymous I've have a MFC-8500 here at work and got an error 77 after removing the fuser to get a huge Brother Mfc 8840d Scanner Software It should say Maintenance in the display.If not press function,*,2,8,6,4 within two seconds.
What to do: Error Code: 50 Error Code: Replace Drum Unit: The drum unit has printed the amount of pages specified for its life cycle. Brother Mfc 8840d Driver Windows 7 Explanation: Check that the document is set correctly on the feeder, and that it is not skidding. Maybe in another article I will write about replacing the fusing asembly if it needs to be done.Below I have provided a link to purchase a new fuser if needed and Press function, *, 2,8,6,4 all within 2 seconds to place the machine into the maintanence mode.
If nothing is found you will need an engineer to check the paper sensors. Brother Mfc 8840d Change Drum Soon If the error persists, then the document feed rollers may need replacing. My# is 410-414-3282 by unknown on Nov 9, 2010 at 12:35pm Add comment Please sign in to comment 0 Thank You, Thank You, Thank You!! Just wanted to report that my MFC-8860DN suddenly locked up during a scan job.
Brother Mfc 8840d Driver Windows 7
If the error persists then the fuser will need replacing. If error persists the document feed rollers or separation pad may need replacing. Brother Mfc 8840d Driver by unknown on Jan 28, 2007 at 2:40pm Add comment Please sign in to comment 0 I have alternating Machine Error 77 & Machine Error 76...Have tried power cycling several times, Brother Mfc 8840d Manual by Anonymous on May 9, 2005 at 8:05am Add comment Please sign in to comment i have also a problem with my printer with the answer in his desktop MACHINE ERROR
However, they can be prone to 76, 77, 78 Fuser / machine error. this content What to do: Machine Error: 88 Error Code: Paper Jam Error: The machine has detected a paper jam in its feed path. Explanation: An engineer wil be required to replace the waste ink box and reset the waste ink counter. Explanation: Check for obstructions in the printhead area. Brother Mfc 8840d Drum
The machine error 77 came up. What to do: Machine Error: 76 Error Code: Heater harness error: This error refers to the fuser unit. Not finding what you are looking for? http://krokmel.com/brother-mfc/brother-mfc-8840d-error.php You have fixed my machine!
Otherwise, it will stop in the middle, giving me "paper breadspread", or else not print at all. Brother Mfc 8840d Service Manual touch print... It should say maintenance in the display.
I called Brother and they had me bring the machine up in maintenance mode and press 31 then 39 the machine seemed to be fixed but now the machine doesn't want
As soon as I turn it on it will say please wait then it will go right into printer Jam. If not then we will have to put it in Maintenance Mode to attempt to manually clear the 76, 77, 78 Fuser / machine error . The best I can figure out is that it has something to do with the fuser or the heat thermostat. Brother Mfc 8840d Troubleshooting This is collected in a container which is now full.
What to do: Error: 71 Error Code: Laser Error: The laser unit is the part of the machine that writes the information onto the drum surface and the machine is detecting This will test if the machine canprint.Many thanks for this post. Press the "Menu" key down, then while holding down the "Menu" key, turn the printer on3. http://krokmel.com/brother-mfc/brother-mfc-8840d-error-a6.php I don't know the technical words to describe what I did, but: Took the drum and toner out, separated toner from drum.Saw that the bluish cylinder in the drum unit had
I tried most of the other instructions listed on this website and got nowhere. Turn off and unplug printer2. I did a parameter reset like Laserman suggested and it worked on my intellifax 4100e. Wait a few more seconds and enter *995.
This content is provided “AS IS” and is subject to change or removal at any time. by Anonymous on Mar 7, 2007 at 6:33pm Add comment Please sign in to comment 0 Hi I'm a bit confused..... - is this a throw away?? What to do: Error: 72 Error Code: Laser Error: The laser unit is the part of the machine that writes the information onto the drum surface and is cannot detect the Thank you everyone for your help!
Press 0,1 to perform a parameter reset. I have been advised that MACHINE ERROR 78 is related to the fuser's thermistor. I tried the tip pull out the toner and put it back, it didn't work. What to do: Machine Error: 83 Error Code: Paper Jam Error: The machine has retried to pull in the paper but failed.